Pololu RC Switch with Medium Low-Side MOSFET

Using the RC Switch

The Pololu RC switch with medium low-side MOSFET can be used with standard hobby radio control systems for radio control switch applications or simple interface applications. Example uses include converting extra RC receiver or servo controller outputs to simple high/low signals that can control LEDs or relays and connecting RC systems to microcontroller projects that do not have the necessary resources for decoding the RC interface. Two outputs indicate the presence of a valid signal and whether the switch is on or off, and an integrated low-side MOSFET turns on when the switch is on, allowing the board to drive moderate loads directly. The switch also features a flyback (or freewheeling) diode across the load outputs so that you can connect a coil to them, such as a motor or relay, without any additional external components. An onboard regulator allows the switch to be powered from voltages between 2.5 V and 16 V. This allows the board to be powered from a 4- or 5-cell NiMH or NiCD battery pack. The battery pack will typically be connected to an RC receiver or servo controller, which passes the power on to the RC switch. The board’s MOSFET can deliver up to 15 A with VCC at 5 V and can handle load supply voltages up to 30 V. The RC switch measures the width of incoming RC pulses and compares it to a user-configurable threshold (with ±64 µs of hysteresis) to decide whether to turn on the MOSFET. By default, the threshold is approximately 1700 μs, with switch activation occurring above the threshold (longer pulses), but the switch has a learning mode that allows you to change the threshold and the activation direction. A safe-start feature reduces the likelihood of unexpected activation.

Outputs and Indicator LED

The RC switch provides feedback about what state it is in via a yellow indicator LED. Status information is also provided on two output pins:

  • The GOOD pin indicates the presence of a valid RC signal (10–330 Hz pulse rate, 0.5–2.5 ms pulse width).
  • The OUT pin indicates whether the MOSFET is on.

When these outputs are high they will be at the same voltage level as VCC. When low, these outputs will be at 0 V (ground). These outputs do not have resistors in series with them. Each output can source or sink up to 25 mA.

Included Hardware

A 12-pin 0.1" straight breakaway male header and two 3.5mm 2-pin terminal blocks are included with the Pololu RC switch with medium low-side MOSFET. The header pins can be used to connect the RC switch to perfboards or breadboards. Please note that the included terminal blocks are only rated for 10 A; for higher power applications, use thick wires soldered directly to the board.

Dimensions

Size: 0.6″ × 0.825″
Weight: 1.2g

General Specifications

Minimum operating voltage: 2.5 V
Maximum operating voltage: 16 V (See Note 2)
Maximum output current: 15 A

Notes

  1. Without included hardware.
  2. Maximum MOSFET voltage; the flyback diode is only rated for 20 V.
  3. RC IN pin can tolerate a maximum of 7 V and has a minimum high threshold of 1 V.

This RC switch converts hobby radio control pulses to digital on/off signals and has an integrated medium, low-side MOSFET that allows it to drive moderate loads (up to around 15 A), such as lighting or small actuators. The activation threshold and direction are configurable, and a safe-start feature reduces the likelihood of unexpected activation. The board also includes a linear regulator that allows it to be powered with voltages between 2.5 V and 16 V.

This compact unit measures a mere 0.6" x 0.8" and weighs just over a gram (0.04 oz) without the included header pins.

We offer a version of this RC switch without a MOSFET for applications that just require a low-current digital signal and a version with a small-sized MOSFET for applications that only need to switch a few amps.


Pololu RC Switch with Medium Low-Side MOSFET

  • Product Code: TE-157-002
  • Brand: Pololu
  • MPN: 1211/2803
  • Availability: 9 In stock
  • $8.44



Related Products

Pololu RC Switch with Digital Output
Pololu RC Switch with Digital Output

The Pololu RC switch with digital output can be used with standard hobby radio control systems for r..

Product Code: TE-157-000

$5.58

Pololu RC Switch with Small Low-Side MOSFET
Pololu RC Switch with Small Low-Side MOSFET

The Pololu RC switch with small low-side MOSFET can be used with standard hobby radio control system..

Product Code: TE-157-001

$6.52