Servo Controllers

This small synchronous switching step-down regulator takes an input voltage of up to 36 V and reduces it to 12 V. The board measures only 0.7″ × 0.7″ yet delivers a typical continuous output current of up to 2.2 A and features reverse voltage protection.

This small synchronous switching step-down (or buck) regulator takes an input voltage of up to 38 V and efficiently reduces it to 5 V. The board measures only 0.7″ × 0.8″, but it allows a typical continuous output current of up to 5 A.

The Micro Maestro is the smallest of Pololu’s second-generation USB servo controllers. The Maestros are available in four sizes and can be purchased fully assembled or as partial kits.

Three channel servo tester with a 4.8-6V input.

The SN74LS241N Tri-State Buffer allows you to toggle an output between the input and high-impedence. This is useful when working with 1-wire TTL interfaces such as the Dynamixel Servos.

The SN74LS241N Tri-State Buffer allows you to toggle an output between the input and high-impedence. This is useful when working with 1-wire TTL interfaces such as the Dynamixel Servos.

240mm 4 pin Servo / Sensor cables for Dynamixel Servos. Set of 10. Made by Robotis.

200mm 4 pin Servo / Sensor cables for Dynamixel Servos. Set of 10. Made by Robotis.

180mm 4 pin Servo / Sensor cables for Dynamixel Servos. Set of 10. Made by Robotis.

140mm 4 pin Servo / Sensor cables for Dynamixel Servos. Set of 10. Made by Robotis.

100mm 4 pin Servo / Sensor cables for Dynamixel Servos. Set of 10. Made by Robotis.

60mm 4 pin Servo / Sensor cables for Dynamixel Servos. Set of 10. Made by Robotis.

The CM-700 is a new Robotis controller with an on-board programmable CPU that features a simultaneous TTL and RS485 communication circuit to control AX-12/18 and DX/RX/EX Dynamixel servos.

Connectors for the OpenCM9.04-A to connect the Dynamixel Servos by Robotis.

The Robotis SMPS 12V 5A PS-10 is the BIOLOID power supply and charging device. This power supply also supplies power for the LIPO Battery Charger LBC-10. Perfect for Dynamixel Servos.

Servo / Sensor cables for Dynamixel Servos. Set of 25. Made by Robotis.

The Open CM9.04 C is the new open source microcontroller from ROBOTIS. This controller is powered by a 32bit ARM Cortex-M3 processor. Any 3-pin TTL DYNAMIXEL servo can be used with the Open CM9.04 C. OpenCM9.04-C.

This device provides power from the SMPS to Dynamixel servos. Connect the SMPS(for CM-5) to the DC terminal and connect the Dynamixel using the cable. There are two 3P connector for AX series and two 4P connector for DX/RX series. SMPS2Dynamixel.

Control a network of Robotis Dynamixels from your PC's USB port! The USB2Dynamixel adapter has three output options: TTL-level RS-232, RS-485, and an RS-232 DB9 serial port.

From Robotis, the CM-2+ is the controller board used to control the Dynamixel DX-series, RX-series servos that support RS-485 and AX-series servos which support TTL level.

The Pololu serial 8-servo controller allows you to control up to eight RC servos with almost any robot controller or computer. Connect multiple units to the same serial line to control up to 128 servos independently.

The 24-channel Mini Maestro 24 raises the performance bar for serial servo controllers with features such as a native USB interface and internal scripting control.

The 18-channel Mini Maestro 18 raises the performance bar for serial servo controllers with features such as a native USB interface and internal scripting control.

The 12-channel Mini Maestro 12 raises the performance bar for serial servo controllers with features such as a native USB interface and internal scripting control.

The Micro Maestro is the smallest of Pololu’s second-generation USB servo controllers. The Maestros are available in four sizes and can be purchased fully assembled or as partial kits.

The Basic Micro ARC32 is a state of the art servo controller and robotics controller. It utilizes a hybrid hardware solution to drive 32 servos with less than 1% CPU time.