SuperDroid Robots
Robots, Parts, & Custom Solutions
Request A Quote
##GOOGLEPLUS##
##PINTEREST##
Category
An assortment of unidirectional and bidirectional Hall effect-based current sensors. They offer a very low-resistance current path and electrical isolation between the current source and the measuring circuit.
Category List
Pololu ACS711 Current Sensor Carrier -12.5 to 12.5A
Item Details
Pololu ACS711 Current Sensor Carrier -12.5 to 12.5A
Item Name:
Pololu ACS711 Current Sensor Carrier -12.5 to 12.5A
Item #:
TS-052-012
Manufacturer:
Pololu
MPN:
2197
Your Price:
$6.95
Availability:
14 Ready to Ship!
Quantity:

Product Image Gallery:

Description:

This current sensor is a carrier board or breakout board for Allegro's ACS711KLCTR-12AB-T Hall effect-based linear current sensor with overcurrent fault output; we therefore recommend careful reading of the ACS711 datasheet (489k pdf) before using this product. The sensor has an operating voltage of 3 - 5.5 V and an output sensitivity of 110 mV/A when Vcc is 3.3 V (or 167 mV/A when Vcc is 5 V).

Features and Specifications:

  • Designed for bidirectional input current from -12.5 to 12.5 A (though the robust sensor IC can survive up to five times the overcurrent condition).
  • Conductive path internal resistance is typically 1.2 mΩ, and the PCB is made with 2-oz copper, so very little power is lost in the board.
  • Use of a Hall effect sensor means the IC is able to electrically isolate the current path from the sensor's electronics (for applications up to 100 V), which allows the sensor to be inserted anywhere along the current path and to be used in applications that require electrical isolation.
  • 100 kHz bandwith.
  • Good accuracy and reliability: factory calibration results in a typical total output error of ±5% at room temperature, the output offset voltage is extremely stable, and the sensor has zero magnetic hysteresis.
  • Overcurrent FAULT output latches low when current magnitude exceeds 12.5 A.
  • Operating temperature range of -40°C to 125°C.

The pads are labeled on the bottom silkscreen, as shown in the picture to the right. The silkscreen also shows the direction that is interpreted as positive current flow via the +i arrow.

This 12.5 A current sensor is marked with a purple X; you can distinguish the versions by reading the text on the IC or by looking at the color of the X on the bottom silkscreen.

Electrical Connections:

The sensor requires a supply voltage of 3 - 5.5 V to be connected across the Vcc and GND pads, which are labeled on the bottom silkscreen. The sensor outputs an analog voltage that is linearly proportional to the input current. The quiescent output voltage is Vcc/2 and changes by 110 mV per amp of input current (when Vcc = 3.3 V), with positive current increasing the output voltage and negative current decreasing the output voltage. For an arbitrary input current i (in amps), the sensor's output voltage can be more generally represented as:

VOUT = (0.11 V/A * i + 1.65 V) * Vcc / 3.3 V

The FAULT pin is normally high and latches low when the current exceeds ±12.5 A. Once the FAULT pin is latched low, the only way to reset it is by toggling power on the Vcc pin.

ACS711 current sensor carrier with solderless ring terminal connectors (not included).


ASC711 current sensor carrier connection and mounting dimension diagram.

The input current can be connected to the board in a variety of ways. Holes with 0.1", 3.5 mm, and 5 mm spacing are available as shown in the diagram above for connecting male header pins or terminal blocks. For high-current applications, you can solder wires directly to the through-holes that best match your wires, or you can use solderless ring terminal connectors, as shown in the picture above. The large through-holes are big enough for #6 screws.

Mounting information:

The board has two mounting holes on the logic side of the board. These mounting holes are 0.5" apart and are designed for #2 screws.

Included components:

This board ships assembled with all surface mount components, and a 5 x 1 strip of 0.1" header pins is included but not soldered in, as shown in the picture shown in Product Image Gallery.

Schematic diagram:


ACS711 current sensor carrier schematic diagram.

Dimensions:

  • Size: 0.7 x 0.8"
  • Weight: 1.3 g (see Note 1)

General Specifications:

  • Current sense: 0.110 V/A (see Note 2)
  • Minimum logic voltage: 3 V
  • Maximum logic voltage: 5.5 V
  • Supply current: 4 mA

Notes:

  1. Without included hardware.
  2. When Vcc is 3.3 V. This specification is proportional to Vcc.

Documentation:

 



This board is a simple carrier of Allegro’s ±12.5A ACS711 Hall effect-based linear current sensor with overcurrent fault output, which offers a low-resistance (~1.2 mO) current path and electrical isolation up to 100 V.
Support Links
Related Items
Pololu ACS714 Current Sensor Carrier -5 to 5A
TS-052-005

This board is a simple carrier of Allegro’s ±5A ACS714 Hall effect-based linear current sensor, which offers a low-resistance (~1.2 mO) current path and electrical isolation up to 2.1 kV RMS.

$9.95
48 Ready to Ship!

Pololu ACS714 Current Sensor Carrier -30 to 30A
TS-052-030

This board is a simple carrier of Allegro’s ±30A ACS714 Hall effect based linear current sensor, which offers a low-resistance (~1.2 mO) current path and electrical isolation up to 2.1 kV RMS.

$8.95
24 Ready to Ship!

New Items
MLT-42-W Watertight Compact Inspection Robot with PTZ Camera
TP-631-100

This easy-to-use tracked robot is designed for tight spaces and low ceilings. It has a full pan and tilt camera with 30X optical zoom. Multiple control options including wireless or tethered using a tablet with a video display.

$7,857.40
Built to Order
4-8 weeks
Cable for Garmin LIDAR-Lite v3
TE-292-000

Hook-up cable for LIDAR-Lite V3 Laser Rangefinder. Can be used hookup the LIDAR Lite V3 Range finder or for multiple projects.

$4.99
200 Ready to Ship!
Powered by SuperDroid Robots, Inc