SuperDroid Robots
Robots, Parts, & Custom Solutions
##GOOGLEPLUS##
##PINTEREST##
cww trust seal
Category
These are our current on sale boards and modules.
Optical IR Sensors. IR distance sensors make it easy to detect and range objects.
Category List
QTR-3RC Reflectance Sensor Array - ON SALE
Item Details
QTR-3RC Reflectance Sensor Array - ON SALE
Item Name:
QTR-3RC Reflectance Sensor Array - ON SALE
Item #:
TS-063-000
Your Price:
$4.95  $2.50
Availability:
58 Ready to Ship!
Quantity:

Product Image Gallery:

Description

This compact module packs three IR LED/phototransistor pairs onto a 1.25″ × 0.3″ board. The sensors are mounted on a 0.375″ pitch, allowing this array to be used as a minimal detector for a line-following robot. Each sensor provides a separate digital I/O-measurable voltage output.

The QTR-3RC reflectance sensor array is intended as a line sensor, but it can be used as a general-purpose proximity or reflectance sensor. The module is a convenient carrier for three IR emitter and receiver (phototransistor) pairs. With sensors spaced at intervals of 0.375″ (9.525 mm) along of the board’s longer axis, this array works well as a minimal detector for line-following robots, as line-following courses are commonly made using 3/4″ (19 mm) black electrical tape. The middle sensor is slightly offset along the short axis of the board.

Each phototransistor uses a capacitor discharge circuit that allows a digital I/O line on a microcontroller to take an analog reading of reflected IR by measuring the discharge time of the capacitor. Shorter capacitor discharge time is an indication of greater reflection.

The LED current-limiting resistors are set to deliver approximately 17 mA to the LEDs when VCC is 5 V, making the total board consumption just over 50 mA. The schematic diagram of the module is shown above:

Interfacing the QTR-3RC Outputs to Digital I/O Lines

Like the Parallax QTI, the QTR-3RC module has three identical sensor outputs that require a digital I/O line capable of first charging the output capacitor (by driving the line high) and then measuring the time for the capacitor to discharge through the phototransistor. This measurement approach has several advantages:

  • No analog-to-digital converter (ADC) is required
  • Improved sensitivity over voltage-divider analog output
  • Parallel reading of all three sensors is possible with most microcontrollers

The typical sequence for reading a sensor is:

  1. Set the I/O line to an output and drive it high
  2. Wait several microseconds to give the 2.2 nF capacitor node time to reach 5 V
  3. Make the I/O line an input (high impedance)
  4. Measure the time for the capacitor node to discharge by waiting for the I/O line to go low

These steps can typically be executed in parallel on multiple I/O lines.

With a strong reflectance, the discharge time can be as low as several dozen microseconds; with no reflectance, the discharge time can be up to a few milliseconds. The exact time of the discharge depends on your microcontroller’s I/O line characteristics. Meaningful results can be available within 1 ms in typical cases (i.e. when not trying to measure subtle differences in low-reflectance scenarios), allowing up to 1 kHz sampling of all three sensors.

Features and Specifications

This module has two mounting holes intended for #2 screws (not included); if the mounting holes are not needed, the ends of the PCB can be ground off to make the unit even smaller (less than 1″ wide). The reflectance sensor array ships with a 1×5 straight male header strip and a1×5 right-angle male header strip as shown above. You can also solder wires, such as ribbon cable, directly to the pads for the smallest installation.

  • Dimensions: 1.25″ × 0.3″ × 0.1″ (32 mm × 8 mm × 3 mm) (without header pins installed)
  • Operating voltage: 5.0 V
  • Supply current: 50 mA
  • Output format: 3 digital pulse signals
  • Optimal sensing distance: 0.125" (3 mm)
  • Maximum recommended sensing distance: 0.25" (6 mm)
  • Weight without header pins: 0.02 oz (0.6 g)
  • Size: 1.25″ × 0.3″ (See Note 1)
  • Weight: 0.6 g (See Note 2)
  • Supply current: 50 mA

Note 1: Mounting holes can be cut/ground off to decrease with to under 1″.
Note 2: Without included optional headers.

Documentation and Support

 



This compact module packs three IR LED/phototransistor pairs onto a 1.25″ × 0.3″ board.
Support Links
Related Items
Pololu Zumo Reflectance Sensor Array
TS-060-000

The Zumo reflectance sensor array provides an easy way to add line sensing or edge detection to a Zumo robot. It features six separate reflectance sensors, each consisting of an IR emitter coupled with a phototransistor.

$9.95
9 Ready to Ship!

QTR-3A Reflectance Sensor Array - ON SALE
TS-064-000

This compact module packs three IR LED/phototransistor pairs onto a 1.25″ × 0.3″ board. The sensors are mounted on a 0.375″ pitch, making this array a great minimal sensing solution for a line-following robot.

$4.95  $2.50
15 Ready to Ship!

New Items
Configurable - HK1500-DM6-E, 6WD All Terrain Autonomous Development Platform
TP-195-006

This is an Enclosed 6-wheel drive robot. Ideally suited for Autonomous Robot Development! It uses six powerful wheelchair motors and the inside robot cavity has plenty of room for electronics.

$13,195.00
Built to Order
4-8 Weeks
PCS-250 24VDC 120 RPM Wheel Chair Motor with Electric Brake
TD-316-120

This is powerful wheelchair motor. They make great heavy-duty robot motors. 250W 120RPM motors with 17mm keyed shaft output. They are sold individually and have an electric brake mounted on the back.

$218.00
12 Ready to Ship!
Powered by SuperDroid Robots, Inc