This robot is our smaller treaded robot that can be used to climb stairs. It can climb over many obstacles that are a lot taller than itself by using the flipper arms. The robot's flipper arm can lift its nose up, stabilize it from flipping over, and/or lift itself up. The arms can also be used to right itself after flipping over. Several different motors, battery options, and motor controllers can be selected with this robot it. Read this entire write-up to help you choose the correct options located at the bottom of this page. After selecting the options you can click the update price to see the adjusted price with your chosen options. The minimum recommended options are already chosen below and reflected in the adjusted price. As shown the robot has an the optional paint and top cover.

We have added a support page for this robot kit that also includes some videos of the robot and its flipper arm in action. See our Treaded LT Support Page!

This robot is not meant for carrying heavy loads or pulling heavy objects like our HD2 Treaded Robot. The robot is a light weight tough little robot that can go over and under many obstacles. With the flipper arm it is highly maneuverable. The front wheels are driven with powerful IG52 gear motors with #25 chain. The chassis is made from aircraft grade aluminum. The design uses all laser cut parts with mortise and tenon design for precise alignment and mating of the parts. We weld all the aluminum together using TIG and MIG for a solid chassis. The top of the robot is open and can be enclosed with an acrylic cover. The treads are driven by powerful motors and the flipper arm allow this robot to ascend and descend stairs. We have designed this robot to be as simple as possible without compromising its strength, durability, or functionality.

The robot axles are solid high strength steel so they will not bend when the robot is dropped. The rear shaft is mounted on sealed needle bearings and keyed to accept the machined flipper arms and the chain sprocket going to the IG42 22 RPM gear motor on its machined mounting bracket.

The robot chassis is symmetric and invertible. The robot can be driven by a simple RC system, one of our custom controllers, or a PC. Contact us for providing a custom control solution. See our Military and Law Enforcement page for some custom control solutions we have provided.

The robot has the ability to climb stairs and go over most terrain. We have spent a lot of time developing this robot so you can use it from the beginning with no issues. The treads are 4" wide with an aggressive All-Terrain rubber pattern. The treads are reinforced with a nylon mesh with a black rubber tread. We put on tracking guides using a custom jig. We then coat the inside with a highly abrasive resistant high traction rubber to grab the 6inch custom drive wheels. The chassis is 3inches high x 8.25inches wide x ~18.5inch wheel center distance length. The total width of the robot is about 17inches wide with the flipper arms. The center cavity is large enough for for the motors, batteries, electronics, cameras, etc. The top is flanged with laser cut holes that are tapped for mounting an acrylic cover. The robot is currently geared with a 1:2 reduction (gear motor to drive wheels). Custom gearing can be requested. The OD of the wheels with the tread is about 6.5 inches, so with the recommended Type 02 IG52 290 RPM motors ground speed is about 4 ft/sec.

Click on pictures for larger views

Standard Items:

Standard Items that come with this kit are as follows:

• Welded Aluminum Base for 52mm Motors (qty 1)

• Two friction drive treads with 4 matched 6 inch custom wheels

• Custom tread tensioning blocks.

• A custom machined flipper arm with a IG42 22RPM motor

• Electric Motor Hookup Kit - TE-024-000 (Qty 3)

• Electric Power Hookup parts (Wire, fuses, switch, connectors, etc.)

• All necessary hardware, bearings, chains, sprockets, etc.

Gear Motor Options:

Different gear motors can be selected in the options section. The robot weighs around 31 pounds with two 2200 24V NiMH battery packs. Its capable of carrying another ~10 lbs. The robot itself is designed to carry even more weight, but since its skid steering, turning in deep grass, carpet etc will be difficult with heavy loads. You should opt for the Type 02 IG52 103 RPM motors or the Type 04 IG52 285 RPM motors if you are going to load it up with heavy loads. We now offer IG52 gear motors with encoders. Review the spec sheets for the individual gear motors to determine typical current draw.

Battery Options:

For the motor batteries, you can choice from 1 to 4 24V 2200mAHr battery packs. We recommend two 24V 2200mAHr battery packs. You can also opt to put your own batteries in the robot too. The NiMH batteries can be run in parallel, but should be charged individually. See schematic for recommended wiring. Don't forget to get your battery chargers either.

Battery Mount Options:

Drive Motor Controller Options:

For the drive motor controllers, you can choice either of these options. The MD03 is a single channel so you need 2 (one per side). The Sabertooth is only rated for 30V max. NiMH batteries will charge to around 30V so you would be at the very limit of these controllers. If using a Sabertooth, either the 10A or 25A can be used, but the 10A will be overloaded in a stall condition.

• Sabertooth Dual 25A Motor Driver - TE-091-225 (Qty 1)

• Sabertooth Dual 10A Motor Driver - TE-091-210 (Qty 1)

• MD03 Devantech 20A 50V Motor Driver - TE-036-000 (Qty 2)

Flipper Motor Controller Options:

For the flipper motor controller, you can choice from a couple different options. The flipper arm uses a IG42 22RPM motor so a simple PWM can be used, but is slightly undersized in a stall condition. The SyRen is only rated for 30V max. NiMH batteries will charge to around 30V so you would be at the very limit of these controllers.

• PWM Motor Controller 3A 12-55V - TE-058-000 (Qty 1)

• SyRen 10A Regenerative Motor Driver - TE-098-110 (Qty 1)

Painting Options:

The pictures as shown are painted a satin black. The chassis is aluminum and as a default, it will be supplied with a wire brushed aluminum look. As an option the robot chassis can be sandblasted and painted a Satin Black.

Assembly Options:

You may purchase this kit assembled or as a kit. Either way you get access to our assembly manual. We recommend full assembly of the robot. Full assembly will include all the mechanical assembly and wiring of the robot for the options selected.

Additional Information:

We build these kits as they are ordered. Please allow 1-3 weeks for shipment. This is a large and heavy package. The price includes building a custom wooden shipping crate. The shipping costs will be calculated upon checkout, the robot and crate weigh about 50lbs.

This kit does not include a microcontroller, sensors, or RC unit. See our Treaded LT Support Page and our ATR Robot Building Page for options and links to our controllers, sensors, and controller batteries. Don't forget to get your battery chargers either.